Join our mailing list! 
Receive Special Offers
and  Monthly new tech info!

Credit Card Processing

  Home > Shop By Brand > Laticrete > Transform >

StoneTech High Gloss Finishing Sealer (Water-Based)
StoneTech High Gloss Finishing Sealer (Water-Based)

Alternative Views:

Water-based, low-VOC, low-odor formula provides a brilliant shine and protects against water- and oil-based stains.

Item# Item Name Our Price Sale Price Qty Add
D15145307 ST311-0632 High Gloss Finishing Sealer (Water-Based) Quart
Add to cart for better price
D15145318 ST311-0401 High Gloss Finishing Sealer (Water-Based) Gallon
Add to cart for better price
Check the items you wish to purchase, then click

Two-in-one formula leaves a wet-look finish and protects against stains Easy-to-use, water-based formula Interior use

Technical Specs:

Where to Use
Slate, saltillo, limestone, travertine and concrete floors.
Notintended for use on glazed, polished, or non-absorbing surfaces, wood floors & decks, showers, countertops, or near pool areas.

Read entire label before using. Use only as directed. Always test in a small inconspicuous area to determine appropriate application method, achievement of desired results, and to ensure good adhesion. Ensure work area is well-ventilated during application and until surface is dry. Keep children and pets out of the area until foot traffic resumes. Avoid applying in direct sunlight. Surface must be thoroughly clean, dry, and free of any sealers or coatings before application. Application to a dirty or dusty surface will affect adhesion and appearance. High Gloss Finishing Sealer should not be applied to a wet or moist surface. Avoid applying onto surfaces not intended for treatment. For new installations, sealer can be applied as soon as 48–72 hours after grouting. Fresh concrete slabs require a minimum of 28 days to cure before applying the sealer.

1. Liberally apply 2–4 even coats with a natural bristle brush, roller, or paint pad applicator. Do not apply product with a sprayer or sponge. Avoid puddling of liquid during application. Failure to apply a sufficient amount of sealer to the surface may result in an undesirable finish or degradation of the coating. More coats may be applied if desired.
2. Allow 30–45 minutes between coats or until surface is dry to the touch.
3. Surface traffic may begin 12 hours after final application; keep installation dry for a minimum of 12 hours; full cure is achieved in 24–48 hours.
4. Keep surface clean and dry as finished surfaces may become slippery when wet.

Available Sizes (and Coverage)
Quart: 25-75 sq. ft.
Gallon: 100-300 sq. ft.
5 Gallon: 500-1,500 sq. ft.
55 Gallon: 5,500-16,500 sq. ft.

High Gloss Finishing Sealer - Data Sheet


Regulatory Information
Under SCAQMD Rule 1113, VOC = <50 g/L
LEED points qualified product.

Related Products
To maintain your stone’s natural beauty, clean surface as needed with Revitalizer® Cleaner and Protector or Stone & Tile Cleaner.

PRODUCT PERFORMANCE GUARANTEE: If not satisfied with product performance when used specifically as directed, return product to point of purchase for refund or replacement, or contact DuPont StoneTech® Professional at 1-888-786-6343. THIS GUARANTEE SHALL BE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED. ALL WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE DISCLAIMED. DuPont StoneTech® Professional shall not be responsible for any incidental or consequential damages or other remedy over and above purchase price. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you.

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Shop By Brand > Laticrete > Transform
Chemicals > Restoration
Chemicals > Impregnators & Sealers